Replacement CCFL inverter for burnt out CCFL Halos on CCFL headlights. Will not work with LED Halos. Sold individually.
Tools generally needed to install your vehicle Headlights
- A full socket wrench set
- Clean gloves to handle the bulbs
- Painters tape to prevent scratches to your your vehicle
- (Rare) Screw drivers, torque wrenches, etc.
- (For LEDs / Halos) 2 splicers per Halo / LED array
your vehicle Head Light installation procedure
- Inspect the new set of your vehicle headlights to make sure you can complete the installation with the tools you have available.
- For safety, disconnect your vehicle battery's negative battery terminal. If your stereo requires a key code in order to reboot, please be sure you have it before disconnecting the battery. Also, be aware that you will probably have to reset your clocks etc after reconnecting the battery later.
- Park on a level surface facing a wall that you could shine your lights on later to aim your your vehicle headlamps.
- Apply painters tape along the edges of your bumper and grill along the vehicle headlights to prevent any scratches that might occur while removing and installing head lights. If uninstalling your your vehicle front bumper is required, make sure you have a safe surface to place the bumper on and that the working surface below your vehicle is also safe in the event the bumper falls down.
- Without touching the glass, uninstall the stock your vehicle Head Lamp, parking, and signal bulbs (as applicable). Depending on the bulb type, this is usually done by just turning the bulb a quarter turn counter clockwise and pulling back. Some vehicles (especially European vehicles) require a few extra steps, such as unclipping a retaining wire or removing a plate that holds the bulb in. Once the bulb is removed, place them in their original container (if available). If they are cold, you could also store them in a ziplock type of bag.
- Unbolt the bolts on the your vehicle Headlight with a socket wrench. Check the new vehicle headlights to help locate the installation points on the old vehicle head lights.in almost all cases the bolt locations will be exactly the same.
- Install the new your vehicle headlights and bolt in place.
- For your vehicle Crystal Headlights, reinstall the old bulbs into the new headlights. For projectors, install the end of the male bulb wire plugs on the projectors to your vehicle's stock harness. Reinstall the parking and signal light bulbs as applicable.
- For halos, splice the negative wire to your vehicle's parking lights negative wire and repeat with the positive wire.
- Reconnect your battery and turn on your your vehicle headlamps and adjust until they are both level with the vehicle. The adjusters usually consist of gear looking mechanisms on the back or top of the headlight that are turned via a centrally placed screw and are usually.
- Reconnect all connections and tighten all bolts in place.
Are your your vehicle headlights sold by the piece or the pair?
All of our headlights are sold in the full pair. When you pay the listed price, you are receiving the complete set including the right and the left sides.
Are these your vehicle headlights street legal?
To our knowledge, all of the Sonar (aka Spyder) and KS (aka Anzo) brand headlights we sell are street legal as mandated by federal law in the United States. That means basically that they are designed to the specifications set forth by the DOT (United States Department of Transportation). On occasion, DOT may test models to double check for compliance. In cases where these your vehicle headlights fail (rare) DOT will have the companies issue a recall. For such headlights, we can take them back and refund you. For other brands, we can not guarantee DOT compliance. Also, please be advised that you may have local laws that may disallow these sorts of headlights to be used.
Will these your vehicle headlights make my car brighter?
No, unless your old vehicle Head lights are so dirty and yellowed that you could barely see out of them, new your vehicle Head Lamps will not make your light beam any brighter. While projector headlights can change the way light is spread out over the road (wider area), they will not increase overall brightness. The only way to increase brightness is to upgrade to higher wattage bulbs or to install a set of Xenon HID Kit.
How can I prevent my new your vehicle headlights from fogging up or letting moisture inside?
During the first few days of operation, it is normal to see some moisture appear in your your vehicle Headlights. This is due to the small amounts of moisture in the plastic and coating that are evaporated when the headlights are first warmed up during use. This sort of moisture is normal and should disappear within a few days.
To be sure that no external moisture gets into the your vehicle Head Light though, it is a prudent idea to silicone seal the edges. Clear silicone sealant can be found in any hardware store (and some auto part stores), and can be applied to the seam along the vehicle headlights where the clear lens meets the rear housing. The $5-$10 is worth it in the long run to protect your investment.
Also, even if a bulb has died, make sure to keep it installed in the vehicle headlight until you replace it to prevent moisture from entering through the bulb hole.
Can I install Xenon HIDs with these your vehicle headlights?
This depends. Most headlights have the physical space to install HID bulbs, but even if it fits, you should ONLY USE LOW WATTAGE HID kits. Wattages higher than 35w can create too much heat which may end up damaging the headlight. Also, please be advised that most projector headlights convert your stock bulbs to a different type. Thus, you need to buy the appropriate bulb for the specific projector bulb you are using, usually an H1, H3, H7, or 9006.
While installing the Halos or LEDs, how can I tell which wire is positive and which wire is negative?
Generally speaking, black is always going to be negative. If there are two reds, then you can use either or. If you still can not tell, you can use an electrical tester. It's probably faster to just try it though since you have a 50% chance of getting it right, and if it's wrong you automatically know it's the other way.
On the parking light wires, black is almost always going to be negative. In cases where the parking light serves as a signal light as well, the solid color wire will be the positive parking light wire since the striped wire usually is for signaling function.
Can I install my halos to another light such as my signal lights?
Theoretically you can, but we highly recommend against doing so as it will void the warranty on the your vehicle Headlights. This is due to the fact that the constant flashing of the halo leads its life to be decreased dramatically. If you are unable to wire the halos to your vehicle's parking lights, we recommend wiring them to your vehicle's low beams or installing a separate switch.
